Showing results: 331 - 345 of 384 items found.
-
MLS-100 -
Notice
•Stabilized Light Source•1310nm & 1550nm•Very small and lightweight•Controlled by Smartphone or PC via USB or Bluetooth•Smartphone application software and PC software•Li-ion Polymer Rechargeable battery•Battery charging via a USB interface•Universal 2.5mm adapter to accept FC, SC or ST•Reference light source for optical test
-
Model 4896 -
ICS Electronics
* Provides four RS-232/RS-422/RS-485 Serial Channels.* High speed, 115.2 K baud channels include 60 K byte buffers.* > 600 K byte/sec. GPIB data transfer rate.* SCPI commands set serial configuration and GPIB address.* LCD display shows Bus activity, buffer status, serial interface signals and channel settings.* 1 U high rack mount kit mounts one or two 4896s * Includes US 115 VAC Power Adapter, Manual and Support CD.
-
7202ec -
Sealevel Systems, Inc.
The 7202ec low-profile PCI Express serial interface provides two RS-232 serial ports. All modem control signals are implemented for maximum compatibility with a wide range of serial peripherals. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates exceeding 1 Mbps. These features make the 7202ec ideal for data intensive applications that require reliable, ultra-fast throughput rates.
-
60-982-001 -
Pickering Interfaces Ltd.
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
60-982-002 -
Pickering Interfaces Ltd.
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
TESTERLYZER® Frame 4.0 -
Ruetz Technologies GmbH
The TESTERLYZER® Frame 4.0 provides a flexible test environment for vehicle control units in an integrated system and is easily accessible from all sides. Customized adaption is provided for panel designs, control unit holders and cable adapters. A TESTERLYZER® I-Box 4.0 is a standard component of the TESTERLYZER® Frame 4.0 and provides the basis for a wide range of structures for the testing of control units, software and services relating to vehicles in research and development. The backbone of the I-Box provides all signals required with distribution to standardized adapter sockets and interfaces. The modular assembly structure ensures swift and safe setting up of the required test environment.
-
EXC-1553UNET/Px-1760 -
Excalibur Systems, Inc.
The EXC-1553UNET/Px-1760 is an intelligent, single- or dual-channel, MIL-STD-1760 adapter. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the MIL-STD-1760 bus, both in the lab and in the field.The EXC-1553UNET/Px-1760 shares its API with the entire Px family so that applications currently running on PCI, PCIe, ExCARD or PCMCIA boards will run without change on this device.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.In addition the EXC-1553UNET/Px(S)-1760 provides 8 I/O Discrete signals and an IRIG B input.
-
Model 8063 -
ICS Electronics
* Provides 48 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes or data strings.* Transparent data transfer mode.* Fully VXI-11 Compliant plus Raw Socket for easy programming with Visual Basic or C, Agilent VEE and LabVIEW.* 1 U high rack mount kit mounts one or two 8063s.* Includes 100-230 VAC Power Adapter with universal plugs.
-
The Imaging Source, LLC
The Imaging Source 13 megapixel microscope camera has been designed to be a cost-effective, versatile solution for demanding microscopy applications. Featuring Sony CMOS technology, this camera comes equipped with a distortion-free autofocus lens which allows viewers to capture exactly what they see through the ocular rather than being limited to a region of interest. This camera can take the place of the ocular itself or can be screwed into the C-mount - eliminating the need for costly adapters. The camera's USB 3.0 interface makes a full HD preview (at 30 fps) on the host PC a reality.
-
Model JI-300 -
Jupiter Instruments
The JI-300 is a versatile, easy to use PC hosted adapter used to drive I2C communicationsto/from a target device. The desktop unit can be configured to interface a variety of I2Cnetworks. Bus parameters such as clock frequency, duty-cycle, setup and hold times, busvoltage, and pull-up resistor values can be varied. JI-300''s diagnostic features including"excessive clock-stretch", "bus-not-free", and "bus contention" monitoring, as well as statusreporting at the conclusion of each message transaction simplifies I2C trouble-shooting. AWindows software application manages the setup and control of the instrument.Communications and unit power is provided via a USB 2.0 connection.
-
SL1047A -
Keysight Technologies
The Scienlab Charging Discovery System – High-Power Series from Keysight enables you to test charging interfaces of electric vehicles (EVs) and EV supply equipment (EVSE) during high-power charging up to 1,500 V DC and ±600 A DC. With the CDS can perform all necessary conformance and interoperability tests according to worldwide charging standards. Our new solution, which features the separate Scienlab Cooling Unit with interchangeable liquid-cooled charging adapters, also enables a high-power upgrade of the SL1040A Scienlab Charging Discovery System - Portable Series.
-
PMC-SpaceWire -
Dynamic Engineering
Utilize SpaceWire to communicate with the European Space Agency and NASA equipment utilizing the ECSS-E-50-12A specification. SpaceWire is configured using routers to create a heirarchical point-to-point system with high speed parallel paths. PMC SpaceWire implements SpaceWire in a convenient PMC format. With PMC you can install the adapter into PCI [PCIBPMC], cPCI [cPCI2PMC], or processor board pmc slots. The SpaceWire specification calls for LVDS signaling and a specific 9 pin micro-D connector. You can connect the PMC-SpaceWire to other SpaceWire compliant devices without electrical interface issues.
-
OTP2-Modul-Nr002 -
LXinstruments GmbH
The rack serves as the basic framework for your individually designed test system. Various OTP² modules can be installed in the 120 x 60 x 80 cm rack in order to meet the most varied of test requirements.The modular architecture of the OTP (Open Test Platform) is based on a flexible instrumentation matrix, LXI-based sources and measuring devices, combined with a high-quality transfer interface for connecting the test adapters. The systems can easily be expanded with customer- and application-specific functions. We use standardization to build cost-effective systems that still fit your requirements exactly.
-
Extech HD755 -
Extech Instruments Corporation
Offering 11 selectable units of measure, the HD755 Differential Pressure Manometer can serve as a low range/high resolution Gauge or provide Differential Pressure up to 0 to 13.85 in. H2O (inches of water). Max/Min recording and Relative time stamp are useful features, as are HD755's Data Hold and Auto Power Off functions. The 0.5psi HD755 also features Zero function for offset correction or measurement and a built-in USB interface. Comes complete with 9V battery, software with USB cable, AC Adaptor, connection hose, built-in stand, and hard carrying case.
-
Extech HD750 -
Extech Instruments Corporation
Offering 11 selectable units of measure, the HD750 Differential Pressure Manometer can serve as a low range/high resolution Gauge or provide Differential Pressure up to 0 to 138.3 in. H2O (inches of water). Max/Min recording and Relative time stamp are useful features, as are HD750's Data Hold and Auto Power Off functions. The 5psi HD750 also features Zero function for offset correction or measurement and a built-in USB interface. Comes complete with 9V battery, software with USB cable, AC Adaptor, connection hose, built-in stand, and hard carrying case.
